-
product
Relay Buddy PRO Test Kit
191
Relay Buddy is a quick go / no-go tester for the most common automotive relays. With the included adapters, Relay Buddy now tests 5 different relay types and also tests shielded relays. Relay Buddy provides you with an indication of the general health and functioning of the relay switch contacts and coil. It will check the control side of the relay by applying a signal to the relay coil while it checks for proper functioning of the relay contacts. Relay Buddy operates the relay several times during each test session as it watches for consistency in every cycle. Relay Buddy will fail the relay and light the RED LED if any one of the cycles proves unsuccessful during the test session.
-
product
RF Test Spectrum Measurements over CPRI
Integris 3000
Most modern cell tower network configurations place the Remote Radio Head (RRH) at the top of the tower and the baseband unit(BBU) at the bottom of the tower. While this configuration is advantageous for both computational efficiency and mitigation of RF loss across the cable, it means the only place along RF can be accessed is at the top of the tower. This forces field technicians to have to climb the tower to measure and debug RF noise problems.
-
product
UV Lamp Weathering Test Chamber
Sanwood Environmental Chambers Co ., Ltd.
Sanwood is a company with professional research and development, sales of Bench-top UV test chamber,Bench-top UV lamp aging test chamber,Bench-top UV weathering test chamber,Bench-top UV aging test chamber,Bench-top UV aging test chamber for 23 years. Ultraviolet light in the sun is a major contributor to the durability of most materials. We use UV lamps to simulate the short-wave ultraviolet portion of sunlight, which produces very little visible or infrared spectral energy. We can choose UV la...show more -
product
Becker NAV/RMU/RMI/OBS Test Fixture
TA-3320
This NAV test fixture is specific to the requirements for testing Becker Avionics NAV, RMI and RMU products. The panel incorporates specific functionality required for testing these Becker products by the book including special requirements for the RMU 5000 and the IN 3300 series of nav indicators. This BAEE NAV test fixture also facilitates resolver alignment and discrete meter testing through the PG 3300 interface connector. The RM 3300 portion of the panel tests the Becker RMI indicators and ...show more -
product
Stand-Alone Test Fixture
MA 2012/D/H/GR2270/71
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: NoInterface signals max.: 1190Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 17,00 kg
-
product
Automation OT Application Platform
Schweitzer Engineering Laboratories, Inc.
The SEL Blueframe application platform and its enabled applications help you maximize the use of system data and provide you with a scalable and customizable solution that accommodates your system schemes today and in the future.
-
product
Threaded Probes Designed for Connector and Harness Test
Equip-Test Threaded Probes Designed for Connector and Harness Test
-
product
Calibration Test Benches
Nagman Instruments & Electronics Pvt. Ltd
Nagman’s wide range of Calibration Systems – Test Benches, Workstations, Bench-tops & Mobile Units – are designed & executed to serve as Powerful tools for Total Quality Management & ISO Conformance with Accuracies Traceable to International Standards and Total Solution to all Calibration requirements.
-
product
Secondary Injection Relay Test Set
T 1000 PLUS
T1000 PLUS is a protective relay test set especially designed to give the commissioning engineers a multitasking and highly reliable testing equipment.
-
product
SMT & THRU HOLE LOADED BOARD TEST PROBES
SERIES 33
ElectricalMAXIMUM CURRENT:3 amps continuousat working travel, non-inductiveRESISTANCE: At 35 mA test current,20 mOHMS meanMaterials and FinishesPLUNGER: Heat treated berylliumcopper, 24Kt gold plated over nickelBARREL: Nickel silver with preciousmetal clad ID.SPRING: Music wire, silver plated
-
product
Temperature Humidity Test Chamber
Dongguan Kejian Instrument Co., Ltd.
This equipment can simulate different environment condition. It's appropriate for testing material performance, such as resist heat, resist dry,resist humidity and resist cold. That can define performance of material.
-
product
Test Setup For Air Conditioner
SCR ELEKTRONIKS have developed TESTING SET UP FOR SINGLE PHASE / THREE PHASE MOTOR for carrying out Performance Test, Earth Contact Resistance Test, High Voltage Test, Megger Test and Leakage Current Test. It consists of Voltmeters, Ammeters and Wattmeters for observing the values of different parameters. OK / NOT OK lamps are also provided to display the results of Earth Contact Resistance Test, HV test, Megger Test, Leakage Current Test. All tests are provided with tripping cut off concept.
-
product
Website Test Automation - Software Testing for Agile Teams
Usetrace
In Usetrace you automate cloud computers to test your site. How to create accounts, order products and post comments. Cloud computers then automatically repeat these traces, testing your site the way your customers would use it—with real major browsers. Traces run periodically on your site, and every time you update the code. If bugs are found, Usetrace alerts you immediately before your customers experience them and business gets impacted.
-
product
Moisture Resistance/ Humidity Test
This test is performed for evaluating the resistance of component parts and constituent materials to the deteriorative effects of the high-humidity and heat conditions typical of tropical environments. Most tropical degradation results directly or indirectly from absorption of moisture vapor, and from surface wetting. These phenomena produce many types of deterioration, including corrosion of metals; physical distortion and decomposition of organic materials; leaching out of constituent components of materials, and detrimental changes in electrical properties.
-
product
OTP-Based Test System
Power electronics assemblies often cannot be tested using conventional technology for their electrical performance. Due to the adaptability of the instrumentation, the OTP concept offers an ideal platform even beyond the space requirements of several control cabinets. In order to achieve high test flexibility with different assemblies, the system was equipped with three-phase AC sources and AC loads as well as a precise three-phase power meter. DC sources and loads with different current and vol...show more -
product
AC Resonance Test System
Shanghai Guantu Technology Co., Ltd.
AC withstand voltage test is an effective and direct method to identify the insulation strength of electrical equipment. During the operation of power equipment, the insulation will gradually deteriorate under the action of electric field, temperature and mechanical vibration for a long time, including overall deterioration and partial deterioration, forming problems. question.
-
product
PWB Interconnect Stress Test
PWB Interconnect Solutions Inc.
Services to test the reliability of Printed Circuit Boards. PCBs).Coupon Inspection and Electrical Prescreen. Coupon Testing. Failure Location via I/R Photo Imagery. Failure Analysis.
-
product
IEC60529 Flushing Test Device IPX5/6
FC-2
Shenzhen Chuangxin Instruments Co., Ltd.
This Flushing Test device is designed according to terms and conditions of IEC60529,GB4208-2008,GB7000.1-2007,GB4706.1-2005,etc. Accordance with requirements of IPX5/6.Applied to carry out waterprooftest on LED lamps, house hold appliances, electric and electronic products and other electric accessories.
-
product
Temperature Rise Test Panel
2000A
SCR ELEKTRONIKS have developed “TEMPERATURE RISE TEST BENCH FOR MEDIUM VOLTAGE SWITCH BOARDS” to measure rise in temperature at various points as mentioned in standard at junctions. The set-up consists of a True RMS Constant Current Source (to maintain the Current within + / - 1 % of set value with Digital Indication), PC based control system, Temperature data logging on PC, Servo-Controller and other indications. Digital voltmeter Primary Voltage) indicates the position of auto transformer (variac).
-
product
GPS/FMS Universal Test Fixture
TA-3000
This panel was designed to give the avionics shop the capability to test and troubleshoot many of the GPS, GPS/COMM and FMS units on the market today. Breakout jacks are provided for both analog and digital signals that need to be monitored or simulated. A data port update jack is provided as well as Arinc 429 and RS232 loopback switches. Switches for Gillham altitude are provided as well as fuel flow adjustments. An array of annunciators and configuration switches are also provided to verify those outputs and inputs. Optional UUT configuration overlays also availabl
-
product
Backplane Test System
402HV
Our model 402HV is the result of 25 years of high voltage / high pin count test systems experience. We produced our first high voltage system back in 1985. It was programmable up to 600 volts / 600 Mohms and had over 49,000 test points. It could test a 5k point board in less that 15 seconds. Since then we have built hundreds of high voltage test systems, with our highest voltage system capable of testing up to 2000 Volts DC / 1500 Volts AC. (One of our 600 volt systems, built in 1986 is still in operation testing boards for a defense contractor.)
-
product
Strain Gauge Test
This test measures the structural stresses induced in equipment when subjected to various environmental and operational loads. Strain gages, which are resistive devices whose outputs are proportional to the amount that they are deformed under strain, are placed at selected locations to yield stress levels which may then be compared to design allowable limits.
-
product
Environmental Test Chamber
The chamber is produced by SUS304 Steel, the temperature keeping material is produced by Polyurethane hard foam and ultra-fine fibre glass, the doorframe heat insulated by Double high temperature aging silicone rubber door sealing strip.The temperature controller is used by Korean TEMI display in English/Chinese and German Siemens PLC, it can be communicated to PC via RS-232. The temperature accuracy is 0.1 and humidity is 0.1%R.HThe temperature sensor is platinum PT100 Ohms/MV resistor
-
product
Formaldehyde Emission Climatic Test Chamber
TESTEX Testing Equipment Systems Ltd.
The internal test room is made by high quality SUS304 stainless steel; heat insulating material: high density fiberglass wool; insulation material thickness: 80mm.The heat inside the internal room may not be conducted.
-
product
EMF Exposure Test
sXcTEM835
Tests radiofrequency electromagnetic field exposures from mobile communication devices operating in the 900 MHz region (additional frequencies upon request). The setup is based on two Crawford TEM cells that are blindly excited by a fully computer-controlled signal unit.
-
product
Semiconductor Test Equipment
Wewon Environmental Chambers Co, Ltd.
Probe card manufacturing need the semiconductor test equipment. When we designed the thermal testing equipment, Only some commonly used test items are packaged into the IC tester, and the logic function of the verification chip is implemented in a fixed test mode. But as chip products diversify, Some thermal inducing system can no longer do it alonehttps://www.wewontech.com/semiconductor-test-equipment/
-
product
4 + 4 LED Driver Test Panel
SCR Elektroniks make 4+4 LED Driver Test Panel to test the driver one by one.
-
product
Temperature Cycling Test Chamber
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell’s Temperature Cycling test chamber is performed on materials to determine the resistance of exposure to alternating extremes of high and low temperatures.
-
product
Backplane & Cable Test
Backplane and cable test systems from Terotest include LINX, a fixtureless test system. Each LINX test card plugs directly into the unit under test, which removes the necessity for long test cables and fixtures. This is called distributed testing and results in dramatically lowered costs. LINX is extremely easy to use, with a self-learn function or input from CAD.
-
product
Automate Functional Tests
GXtest
With GXtest you can automate functional tests and find bugs in early stages. GXtest is easy to configure, use and maintain. It allows running the necessary tests to ensure the high quality of the generated software, finding errors when solving them is less costly.
